Making Jeweled Bib Necklace
Even though they may have a juvenile moniker, bib necklaces are in fact quite sophisticated and stylish. Named after their shape, bib necklaces are large and pair well having a strapless dress or any outfit using a simple neckline. Making a jeweled one in the home is simple, and will create a stunning and versatile accessory. Such necklaces could cost over $300 inside the stores. However with a couple of craft jewels, you can design your personal for some dollars.
1
Pick a shape to your bib necklace. Take a look at examples in shops and magazines to see what fits your frame along with your style. Some bib necklaces are comprised entirely of metal and jewels -- attached inside a bib-shaped formation -- while other styles use a fabric, bib-shaped backing for the gems. Decide on a bib design, or shape, from the latter category to recreate inside your project.
2
Draw your shape to the piece of white paper, using a pencil, and make the grade out with the scissors. This is the bib pattern.
3
Lay the pattern on top of a piece of the black felt. Trace round the pattern using a bit of tailor's chalk.
4
Stack the 2 bits of felt together with the other person, with the chalk-marked piece at the top. Pin the 2 bits of felt together by putting a pin about the nearly everywhere edges.
5
Cut the bib shape out with the scissors. You'll have two bib-shaped pieces of felt. Set the felt scraps to the side.
6
Trace the bib pattern piece on the blank stencil sheet using a marker. Cut the bib shape out.
7
Place among the felt bib shapes in your office. Apply hot glue to the shape using the hot glue gun. Run the glue across the edge along with a line over the middle. Put the plastic bib shape together with the felt. Line the sides up so they really are even. Squeeze the pieces flat.
8
Operate a type of glue round the side of the plastic. Use a type of glue over the core plastic. Stack another felt bib shape together with the plastic. Line the edges up evenly and squeeze flat.
9
Allow the glue cool for 10 minutes.
10
Put the jewels to the bib. Place them symmetrically, if possible. Have fun with different design combinations unless you are satisfied with it.
11
Pick up a jewel and apply hot glue for the back than it. Place it to the bib in their original place. Do that one by one until all jewels happen to be glued down. Allow glue cool for 10 minutes.
12
Cut the ribbon into two 18-inch pieces.
13
Flip the bib to the trunk. Place one end of a bit of satin ribbon in the right, top edge of the bib. This can produce the ties with the necklace. In case you are unsure where you can position the ribbon, contain the bib up to your neck and mark the area with chalk.
14
Glue the edge of the ribbon for the bib. Repeat for that left affiliate with the other ribbon piece.
15
Cut a small square from your felt scraps. Glue it along with no more one of many ribbons. This covers the raw side of the ribbon and helps make the back from the necklace look neat. Remove and glue another square for that other side.
16
Secure the necklace around your neck by tying the ribbon in to a neat bow with long ends.
1
Pick a shape to your bib necklace. Take a look at examples in shops and magazines to see what fits your frame along with your style. Some bib necklaces are comprised entirely of metal and jewels -- attached inside a bib-shaped formation -- while other styles use a fabric, bib-shaped backing for the gems. Decide on a bib design, or shape, from the latter category to recreate inside your project.
2
Draw your shape to the piece of white paper, using a pencil, and make the grade out with the scissors. This is the bib pattern.
3
Lay the pattern on top of a piece of the black felt. Trace round the pattern using a bit of tailor's chalk.
4
Stack the 2 bits of felt together with the other person, with the chalk-marked piece at the top. Pin the 2 bits of felt together by putting a pin about the nearly everywhere edges.
5
Cut the bib shape out with the scissors. You'll have two bib-shaped pieces of felt. Set the felt scraps to the side.
6
Trace the bib pattern piece on the blank stencil sheet using a marker. Cut the bib shape out.
7
Place among the felt bib shapes in your office. Apply hot glue to the shape using the hot glue gun. Run the glue across the edge along with a line over the middle. Put the plastic bib shape together with the felt. Line the sides up so they really are even. Squeeze the pieces flat.
8
Operate a type of glue round the side of the plastic. Use a type of glue over the core plastic. Stack another felt bib shape together with the plastic. Line the edges up evenly and squeeze flat.
9
Allow the glue cool for 10 minutes.
10
Put the jewels to the bib. Place them symmetrically, if possible. Have fun with different design combinations unless you are satisfied with it.
11
Pick up a jewel and apply hot glue for the back than it. Place it to the bib in their original place. Do that one by one until all jewels happen to be glued down. Allow glue cool for 10 minutes.
12
Cut the ribbon into two 18-inch pieces.
13
Flip the bib to the trunk. Place one end of a bit of satin ribbon in the right, top edge of the bib. This can produce the ties with the necklace. In case you are unsure where you can position the ribbon, contain the bib up to your neck and mark the area with chalk.
14
Glue the edge of the ribbon for the bib. Repeat for that left affiliate with the other ribbon piece.
15
Cut a small square from your felt scraps. Glue it along with no more one of many ribbons. This covers the raw side of the ribbon and helps make the back from the necklace look neat. Remove and glue another square for that other side.
16
Secure the necklace around your neck by tying the ribbon in to a neat bow with long ends.
タグ ：Bib Necklace
Put Crystals on Your Earrings
Crystals certainly are a popular way to personalize and add sparkle with a selection of objects. From expensive hand-cut crystals to less expensive mass-produced acrylic crystals, different size and shapes are available to suit different needs. Jewelry often benefits from the addition of crystals. Crystals put on earrings, as an example, add interest, sparkle plus a new life to a older or ordinary set of earrings.
1、Choose a set of earrings with no less than some flat working surface to adhere urates.
2、Dip a rag in denatured alcohol and wipe on the earrings to eliminate dirt and oils that could hinder the adhesive. 、3
Pick a pattern for your crystal application. Decide on a straight line, flower shape or curve, for instance.
4、Peel one crystal at the same time from your adhesive sheet and set about the earrings in the desired location. Continue adding crystals before the pattern is done.
5、Set the earrings aside and allow the adhesive on the back of the crystals to bond with all the earring material. Keep to the crystal manufacturer's strategies for cure time.
1、Choose a set of earrings with no less than some flat working surface to adhere urates.
2、Dip a rag in denatured alcohol and wipe on the earrings to eliminate dirt and oils that could hinder the adhesive. 、3
Pick a pattern for your crystal application. Decide on a straight line, flower shape or curve, for instance.
4、Peel one crystal at the same time from your adhesive sheet and set about the earrings in the desired location. Continue adding crystals before the pattern is done.
5、Set the earrings aside and allow the adhesive on the back of the crystals to bond with all the earring material. Keep to the crystal manufacturer's strategies for cure time.
